| [1096] | 1 | Puff -- A Simple Inflate
|
|---|
| 2 | 3 Mar 2003
|
|---|
| 3 | Mark Adler
|
|---|
| 4 | madler@alumni.caltech.edu
|
|---|
| 5 |
|
|---|
| 6 | What this is --
|
|---|
| 7 |
|
|---|
| 8 | puff.c provides the routine puff() to decompress the deflate data format. It
|
|---|
| 9 | does so more slowly than zlib, but the code is about one-fifth the size of the
|
|---|
| 10 | inflate code in zlib, and written to be very easy to read.
|
|---|
| 11 |
|
|---|
| 12 | Why I wrote this --
|
|---|
| 13 |
|
|---|
| 14 | puff.c was written to document the deflate format unambiguously, by virtue of
|
|---|
| 15 | being working C code. It is meant to supplement RFC 1951, which formally
|
|---|
| 16 | describes the deflate format. I have received many questions on details of the
|
|---|
| 17 | deflate format, and I hope that reading this code will answer those questions.
|
|---|
| 18 | puff.c is heavily commented with details of the deflate format, especially
|
|---|
| 19 | those little nooks and cranies of the format that might not be obvious from a
|
|---|
| 20 | specification.
|
|---|
| 21 |
|
|---|
| 22 | puff.c may also be useful in applications where code size or memory usage is a
|
|---|
| 23 | very limited resource, and speed is not as important.
|
|---|
| 24 |
|
|---|
| 25 | How to use it --
|
|---|
| 26 |
|
|---|
| 27 | Well, most likely you should just be reading puff.c and using zlib for actual
|
|---|
| 28 | applications, but if you must ...
|
|---|
| 29 |
|
|---|
| 30 | Include puff.h in your code, which provides this prototype:
|
|---|
| 31 |
|
|---|
| 32 | int puff(unsigned char *dest, /* pointer to destination pointer */
|
|---|
| 33 | unsigned long *destlen, /* amount of output space */
|
|---|
| 34 | unsigned char *source, /* pointer to source data pointer */
|
|---|
| 35 | unsigned long *sourcelen); /* amount of input available */
|
|---|
| 36 |
|
|---|
| 37 | Then you can call puff() to decompress a deflate stream that is in memory in
|
|---|
| 38 | its entirety at source, to a sufficiently sized block of memory for the
|
|---|
| 39 | decompressed data at dest. puff() is the only external symbol in puff.c The
|
|---|
| 40 | only C library functions that puff.c needs are setjmp() and longjmp(), which
|
|---|
| 41 | are used to simplify error checking in the code to improve readabilty. puff.c
|
|---|
| 42 | does no memory allocation, and uses less than 2K bytes off of the stack.
|
|---|
| 43 |
|
|---|
| 44 | If destlen is not enough space for the uncompressed data, then inflate will
|
|---|
| 45 | return an error without writing more than destlen bytes. Note that this means
|
|---|
| 46 | that in order to decompress the deflate data successfully, you need to know
|
|---|
| 47 | the size of the uncompressed data ahead of time.
|
|---|
| 48 |
|
|---|
| 49 | If needed, puff() can determine the size of the uncompressed data with no
|
|---|
| 50 | output space. This is done by passing dest equal to (unsigned char *)0. Then
|
|---|
| 51 | the initial value of *destlen is ignored and *destlen is set to the length of
|
|---|
| 52 | the uncompressed data. So if the size of the uncompressed data is not known,
|
|---|
| 53 | then two passes of puff() can be used--first to determine the size, and second
|
|---|
| 54 | to do the actual inflation after allocating the appropriate memory. Not
|
|---|
| 55 | pretty, but it works. (This is one of the reasons you should be using zlib.)
|
|---|
| 56 |
|
|---|
| 57 | The deflate format is self-terminating. If the deflate stream does not end
|
|---|
| 58 | in *sourcelen bytes, puff() will return an error without reading at or past
|
|---|
| 59 | endsource.
|
|---|
| 60 |
|
|---|
| 61 | On return, *sourcelen is updated to the amount of input data consumed, and
|
|---|
| 62 | *destlen is updated to the size of the uncompressed data. See the comments
|
|---|
| 63 | in puff.c for the possible return codes for puff().
|
|---|
